Accusplit Watch AX810T User Manual

Press S2 (upper right) to cycle through  
the fields you can set.The fields are: Time  
setting Alarm On/Off Time setting.  
Press S2 until you see digits in the center  
of the display. Now you can set the timer.  
Press S3+ (lower right) to increase the  
timer set point, and press S3– (lower left)  
to decrease the set point.You will see both  
the digits and also the dial size increase or  
decrease. For a setting of 60 minutes, the  
dial will show completely red.  
Back light  
and Setting  
TIME TIMER  
0
Start,  
Stop, &  
Reset  
Wrist Timer™  
“the difference is the disk”  
30  
Timer  
30M  
WATER RESIST  
TIMER Button  
Press Once to  
Start andTwice  
quickly to Stop.  
Once you have set the desired time, press  
S2 once to change Alarm On/Off Setting.  
Introduction  
TIME TIMER  
Congratulations on your purchase of the  
TimeTimer WristTimer! No other tool  
communicates the concept of elapsed  
time as well as theTimeTimer.Time  
Timer reinforces the sense of elapsed  
time with a graphic depiction of the time  
remaining.  
You will see the word “ON” or “OFF,plus  
0
an alarm  
3 symbol, both flashing. Press  
S3+ or S3– to turn the Alarm on or off.  
Press and  
Hold to Reset.  
Pressing S2 again will return you to the  
Timer setting. Press S4 once (upper left)  
to exit setting mode. Leaving the timer  
unattended for 30 seconds in set mode  
causes it to save any changes and then exit  
set mode.  
30  
30M  
WATER RESIST  
Understanding the Timer  
TheTimeTimerWristTimer™ provides  
a graphical count down timer, using the  
patentedTimeTimer technology. Red  
represents the time remaining.The disk  
diminishes as time elapses until the  
display is blank and no red is visible on  
the timer face.Time elapses in a clockwise  
direction. When active, the Alarm sounds  
to let you know that time has run out.  
To Start the timer, press theTIMER  
Setting Notes:  
button (upper right).  
1. You can either press and release S3+  
and S3– to change field values, or “press  
and hold” either of the S3 buttons to  
rapidly change the field value.  
2. You can return to the default timer  
setting of 60 minutes by simultaneously  
pressing S3+ and S3–.  
To Stop the timer, press theTIMER button  
TWICE, in rapid succession (press the  
button twice within ½ second).  
To Reset the timer, press and hold the  
TIMER button for at least 2 seconds.  
If turned ON, the Alarm will sound  
when time expires.The alarm sounds  
for 5 seconds, or until cancelled by  
pressing any button.  
TIME TIMER  
TIME TIMER  
TIME TIMER  
Changing the Battery  
0
0
0
When the display grows dim or goes out  
entirely, it is time for a new battery. Using  
a small Phillips head jewelers screwdriver,  
remove the four screws holding back of  
timer onto case. Gently slide the old battery  
from its slot, and replace with new CR2025  
Lithium battery. Make sure that the positive  
(“+”) terminal side is facing up.  
Setting the Timer  
The timer must be stopped before changing  
settings.The timer uses a standard setting  
procedure:  
30  
30  
30  
30M  
30M  
WATER RESIST  
30M  
WATER RESIST  
WATER RESIST  
45 minutes  
remaining  
59 minutes  
remaining  
Times up  
Press and hold “S1” to enter setting mode  
Press “S2” to change the field to set  
Press “S3” to change the value of the  
field being set  
Press “S4” to exit setting mode  
To set the timer, press and hold the  
S1 button (upper left) for about three  
seconds, until the numbers in the middle  
begin to flash, indicating that you have  
entered setting mode.  
Power Reset  
The timer also comes with a convenient  
back light, to help you see the display  
in low light conditions. Press the LIGHT  
button (upper left) to turn on the back  
light.  
You can reset the timer to original factory  
settings by pressing S3+ and S3– (the two  
lower buttons) together, and holding for at  
least five seconds.  
Manufactured for  
TimeTimer, Inc.  
7707 Camargo Road  
Cincinnati, OH 45243  
Using the Timer  
S1 & S4  
S2  
The timer can be set anywhere from one  
minute up to one hour.There is an  
audible alarm to let you know when time  
has expired.  
TIME TIMER  
0
(513) 561-4199  
Fax (513) 561-4699  
.
The timer comes from the factory set  
to one hour, and the audible alarm set  
to OFF.  
Alarm is On  
S3+  
1-877-771-TIME  
(1-877-771-8463)  
30  
30M  
WATER RESIST  
To change the settings, see the following  
instructions.  
S3–  
U. S. PATENT NO. D369, 619 & 5,662,479  
REGISTER NOW. Please return your AX810T registration to the Repair  
Center address in the warranty, and we will let you know about future products.  
5 YEAR NO-PROOF-OF-PURCHASE LIMITED WARRANTY  
Free service for first year (see back of watch for date). $15 fee applies  
thereafter. Return unit with daytime phone number to: AST Repair Center,  
3090 Independence Drive, Suite 148, Livermore, CA 94551 USA 800-935-1996  
925-290-1900 www.ACCUSPLIT.com • support@ACCUSPLIT.com  
Email ___________________________________________________  
User ____________________________________________________  
Developed by Time Timer LLC, in cooperation with Abilitations,  
“improving the lives of children with special needs”  
#998-311A  
 

Acer Projector PD311 User Manual
Adesso Computer Keyboard WKB 3100UB User Manual
Agilent Technologies Stereo System 32A User Manual
Airlink101 Switch AGSW808POE User Manual
AKG Acoustics Headphones K 430 User Manual
Altec Lansing MP3 Docking Station Portable Speaker Docking Station User Manual
American Audio CD Player DCD PRO 250 User Manual
Apple Network Card RGB IIB User Manual
Bakers Pride Oven Oven CO11 G1 User Manual
BC Speakers Portable Speaker ME10 User Manual